Kyocera Error Codes List: Common C-Codes and What to Do

Short answer: A Kyocera code that starts with C (for example C6000 or C7990) is a service call: the machine found a fault in a part and stopped to protect itself. Write the code down, switch the copier off, wait about a minute and switch it on again. If the code comes back, do not keep restarting the machine. Most C-codes need a technician to repair or replace a part, such as the fuser, a motor, the laser unit or a sensor.
What do Kyocera error codes mean?
Kyocera TASKalfa copiers and ECOSYS printers show three main kinds of messages:
- C-codes (service calls), such as C6000 or C3100. A part has failed or is not working as expected. These usually need a technician.
- J-codes (paper jams), such as J0501. The screen shows where the paper is stuck. You can usually clear these yourself. See our paper jam guide.
- Plain messages, such as "Add toner" or "Replace the waste toner box". These are routine and you can handle them with the right consumable.
The code number tells you which part of the machine the fault is in. The table below lists the codes we see most often on Kyocera machines in Pakistan. Exact meanings can differ slightly by model, so always check the code against your model's service information or ask a technician.
Common Kyocera C-codes and what they mean
| Code | Area | What it usually means | What to do |
|---|---|---|---|
| C0100 | Main board / memory | Backup memory (EEPROM) cannot be read or written | Restart once. If it returns, call a technician — the main board or memory may need service |
| C1010 / C1020 | Paper cassette | Lift motor error in cassette 1 or 2: the paper plate does not rise | Remove the cassette, check nothing is under the plate and the paper is not over the max line, refit firmly and restart |
| C2000 | Drive | Main motor error: the motor does not reach its normal speed | Restart once. If it returns, call a technician (motor, gears or drive board) |
| C3100 | Scanner | Scanner carriage error: the scanner cannot find its home position | Check the scanner lock (if your model has one) is released; restart. If it returns, a technician should check the carriage and cable |
| C3200 | Scanner | Exposure lamp error: the scan lamp is not lighting correctly | Technician — lamp or its board needs checking |
| C4000 / C4010 | Laser unit | Polygon motor error: the laser scanner motor does not run at the right speed | Technician — the laser scanner unit usually needs repair or replacement |
| C4200 | Laser unit | BD (beam detect) error in the laser scanner unit | Technician — laser scanner unit |
| C6000 | Fuser | Fuser heater break: the fuser does not heat up | Technician — fuser heater, thermostat or fuser unit. Do not touch the fuser |
| C6020 | Fuser | Fuser temperature too high | Switch off at once and call a technician. Do not keep restarting |
| C6030 | Fuser | Fuser thermistor break: the temperature sensor gives no reading | Technician — thermistor or fuser unit |
| C6050 | Fuser | Fuser temperature too low / does not reach working temperature | Check the copier is on its own socket with stable voltage; if it returns, technician |
| C7100 / C7101 | Developer / toner | Toner sensor error in the developer unit | Technician — developer unit or toner sensor |
| C7800 / C7801 | Sensors | Outside (room) temperature sensor open or short | Technician — sensor or its cable |
| C7990 | Waste toner | Waste toner box full | Replace the waste toner box. If the code stays with a new box, a technician should check the sensor |
What can I safely do before calling a technician?
- Write down the full code. Note the letter and all the numbers, and what the copier was doing when it stopped.
- Restart once. Switch off with the main power switch, wait about a minute and switch on again. Some codes clear after one restart.
- Check simple things. Make sure all doors and cassettes are fully closed, the waste toner box is not full, and the copier is plugged straight into a wall socket with stable power.
- Stop if the code returns. Do not restart again and again. Repeated restarts with a fuser or motor fault can damage other parts.
- Call a technician. Give the code and your model number (for example TASKalfa 3011i or ECOSYS M2040dn). This helps the technician bring the right part.
Which Kyocera errors should I never try to fix myself?
- Fuser codes (C6000–C6050). The fuser gets very hot, and C6020 means it is overheating. Switch off and call a technician.
- Laser unit codes (C4000–C4200). The laser scanner is a sealed unit and should only be opened by a trained technician.
- Main board and memory codes (C0100 and nearby). Wrong handling can lose machine settings and counters.
Why do Kyocera errors keep coming back?
A code that returns again and again usually means the part is worn, not that the machine "glitched". Common reasons are:
- an old fuser or a weak heater;
- unstable voltage or load-shedding without a proper UPS or stabiliser;
- dust and toner build-up on sensors;
- non-genuine toner or a developer unit near the end of its life.
Regular service visits catch most of these early. On a maintenance contract (AMC), our technicians clean sensors, check the fuser and drive parts, and replace worn parts before they stop your office.
Kyocera parts and repair in Pakistan
Paragon Copier Solution repairs Kyocera TASKalfa copiers and ECOSYS printers at your office, along with Ricoh and Konica Minolta machines. Our technicians carry common parts and can source fusers, drums, developer units and boards. In Karachi and other cities with a Paragon service hub, a technician usually reaches you in about 3 hours. See our Kyocera photocopiers and printers and parts and toner.
Kyocera showing a C-code? Send a photo of the screen and your model number on WhatsApp, and we will tell you the next step or send a technician.
Frequently Asked Questions
What does a C-code mean on a Kyocera copier?
A C-code is a service call. The copier found a fault in a part, such as the fuser, a motor, the laser unit or a sensor, and stopped to protect itself. Restart once; if the code returns, call a technician.
How do I clear a Kyocera error code?
Switch the copier off with the main power switch, wait about a minute and switch it on. If the code was caused by a short glitch it will clear. If it comes back, the fault is real and a technician needs to repair the part.
What is Kyocera error C6000?
C6000 usually means the fuser is not heating up, often because of a broken heater, thermostat or fuser unit. It needs a technician. Do not touch the fuser area.
What is Kyocera error C7990?
C7990 means the waste toner box is full. Replace it with a new waste toner box. If the code stays after replacing the box, a technician should check the sensor.
What is Kyocera error C3100?
C3100 is a scanner carriage error: the scanner cannot return to its home position. Check that any scanner lock is released and restart. If it returns, a technician should check the carriage, belt and cable.
Do you repair Kyocera copiers outside Karachi?
Yes. Paragon has 20+ service hubs across Pakistan and repairs Kyocera, Ricoh and Konica Minolta copiers for offices in all major cities.

















